1/2" Particulate filter water trap seperator moisture Compressed Air Compressor
BRAND NEW !!! New 1/2" Compressed air line Filter water seperator/Particulate Filter. This filter removes liquid and debris from your compressed air line to extend the life of your tools and compressor accessories. 105 CFM Flow Rate 1/2" Female NPT Air Inlet port X 1/2" Female NPT Air Outlet port 5 micron filter element included Visible at a glance, Polycarbonate Bowl to view moisture levels 7 - 150 PSI Max Output Pressure 215 PSI Max Input pressure Equipped with 2.7oz Poly Bowl Temperature ratings between 41f thru 140f Manual twist drain to to release built up liquid and debris from the system. located on the bottom of the bowl. 6.5" Height x 3" wide Installation instructions included Compressed air filters protect your equipment from dust, dirt, oil and water. Dust will wear down your equipment (like the air motor in grinders, pneumatic actuators and it can make pneumatic control valves get stuck. Especially when the dirt and dust is combined with oil (which is often the case with compressors), a sticky mess can form inside valves, motors and other compressed air equipment.
CrocSee C1.8C.027 1/4" NPT Thread 26CFM Automatic Drain Air Compressor Compressed In Line Particulate Moisture Water Trap Filter Separator with Mount
100% satisfaction and RISK FREE warranty: 1 year free replacement or full refund without return If the item you have received is defective in any way, please message us for free replacement or refund without return.
HEAVY DUTY HIGH FLOW COMPRESSED AIR IN-LINE PARTICULATE FILTER WITH METAL BOWL, 3/4" NPT PORTS, 140 CFM, VISIBLE SIGHT GLASS, 5 MICRON ELEMENT
Compressed air filters, also known as line filters, remove contaminates from the compressed air leaving a screw or piston compressor, which often has a high water content and concentration of oil or other contaminants. Compressed air in-line filters extend the life of your tools and equipment down stream. Excess moisture collects in the quick release 1/4 turn metal bowl with. Manual drain. Heavy duty type -- High Air flow and drain capacity. Transparent water level indicator for easy checking. Suitable for any 3/4" high flow air pressure equipment or system. FOR REPLACEMENT 5 MICRON FILTER ELEMENTS. COPY AND PASTE ASIN TO YOUR AMAZON SEARCH B01N7VEJ2V
EDGE Industrial 3/4 HEAVY DUTY INDUSTRIAL 3 STAGE COMPRESSED AIR CLEANER MOISTURE TRAP, COALESCING FILTER, DESICCANT DRYER
3/4" Particulate Filter / Water Trap Coalescing Filter and desiccant dryer combo to clean and dry compressed air lines. In-Line THREE Stage unit includes (1) Particulate Filter / Water Trap - (1) Coalescing Filter - (1) Desiccant Dryer This HEAVY DUTY 3 stage air cleaner system will extend the life of your air tools and prevent costly repairs down the road. Stage 1 particulate filter / water trap with a 5 micron element will remove the majority of the moisture and larger debris and collect at the bottom of the 9oz metal bowl. Stage 2 Coalescing filter has a 0.01 micron filter element and will remove 99.98% of the remaining Moisture Vapor, Oil residue and smaller particulate that may have passed through the Stage 1 filter. Stage 3 Desiccant dryer will dry out the incoming air flow, so you will get perfectly clean dry air down stream to your pneumatic tools and equipment. These systems are highly recommended for paint gun applications and plasma cutters. 3/4" FEMALE NPT INLET X 3/4" FEMALE NPT OUTLET ( Please note that 3/4" NPT measures 1.05" on a tape measure/ruler/caliper) HEAVY DUTY CONSTRUCTION WITH 11oz METAL BOWLS
Pneumatic Plus SAW Series Filter-Regulators, or "Piggybacks" combine the functions of both filter and regulator. Piggybacks are compact and most effective when space is constrained. FILTER: Filtering out of dirt and foreign particles, and the separation of moisture is automatic with air flow. There are no moving parts and no adjustments are necessary. Accumulated sludge and moisture should be drained off. Sediment should not be permitted to fill above the lower baffle. Wash filter element at intervals with methylene chloride or similar cleansing fluid to maintain filtering efficiency. To clean element, depressurize system, pull down the lock and twist off the metal guard and polycarbonate bowl and unscrew element from head. Dry filter element thoroughly before reassembling. Clean filter bowl(s) only with soapy water. Inspect O-ring, replacing if damaged or distorted. Reassemble with care to avoid stripping threads on bowl. After a metal bowl with sight is tightened, it may be rotated up to 180° (for proper viewing.) REGULATOR: Before supplying the air, turn the adjusting knob counter-clockwise until compression is released from the control spring. Turn on the air supply and adjust the knob to set the desired secondary pressure by turning the knob clockwise. Note: Adjustment knob...
AC 110V 1/2" US Plug Electronic Automatic Timed Drain Valve for Compressed Air
Sub-drain valve to simulate circuits and solid state electronic timer solenoid valve to match the compressed air system to achieve automatic timed condensate discharge
Widely used in gas tank, drip legs and other compressed air system components
There are test button and the intervals, emission time adjustment knob
Easy to install, fully automatic operation
Time interval (OFF): 0.5 to 45 minutes
Discharge time (ON): 0.5 to 10 seconds
Manual test button (micro switch)
Power supply voltage: AC110 50HZ
The current consumption of the largest 4mA
Ambient temperature: minus 40°C to 60°C
Shell material: Flame retardant ABS plastic
Electrical connection: DIN43650A
Indicator lamp: LED indicating power on / off
Type: two two direct-acting valve
In / out port size: 1/2"
Maximum working pressure: 1.6Mpa
Maximum temperature: 90°C
Forging brass valve, flow aperture of 5 mm
Insulation: class H
Protection grade: IP65
Voltage range: ±10%
Power Cable about 1.8m Length (US plug)
1 x Automatic Electronic Timed Drain Valve
3/8" in LINE Desiccant AIR Dryer for Compressed AIR Great for Pneumatic Tools Spray Booth Plasma Cutter
3/8" IN-LINE DESICCANT AIR DRYER FOR COMPRESSED AIR SYSTEMS Removes condensate/moisture from compressed air lines and extends the life of your pneumatic tools and equipment. 3/8" FEMALE NPT INLET X 3/8" FEMALE NPT OUTLET 150 PSI MAX Desiccant Air Dryer: 150 PSI MAX PRESSURE 5oz POLYCARBONATE BOWL WITH METAL GUARD Comes with 2 bags of desiccant beads. Beads turn Pink once they're ready to be changed.. Use a standard Oven to dry out desiccant beads up to 3X. please contact us with any questions or inquiries about our products.
MAX. WORKING PRESSURE: 142PSI (10BAR) 1ST STAGE OF PRE-FILTER WITH 5UM FILTER ELEMENT TO REMOVE OIL, WATER & PARTICLES 2ND STAGE OF MICRO-FILTER WITH 0.01UM FILTER ELEMENT TO REMOVE 99.99% PARTICLES AND OIL. 3RD STAGE OF DRYER WITH DESICCANT TO ABSORB THE LEFT WATER. MEET THE STANDARD ISO 8573-1 CLASS 2 APPLICATION: PAINT SPRAY GUN, FLUID, AIR CONDITION SYSTEM, FOOD & BEVERAGE INDUSTR, MEDICINAL TECHNOLOGY, DUST-FREE ENVIRONMENT Brand new 3/4" compressed air inline moisture filter / separator, oilesser, desiccant dryer combonation. This is a top quality 3 part air filter. The first stage of filtration is a 5 micron filter that removes droplets and debris from your air line, the second stage is a .01 micron oilesser that removes oil and oil aerosol, the third filtration stage is a desiccant dryer which removes any remaining moisture or water vapor from your air line. Using this filter in your air system will provide clean, dry air to the rest of your line and can extend the life of your air tools. This is recommended to those that are running a plasma cutter or a paint gun. Getting moisture in your air lines and tools can be a costly mistake and cause a lot of damage to delicate tools, this filtration system allows you the peace of mind to work without worry!
1" HIGH FLOW HEAVY DUTY Particulate filter for compressed air systems air compressor CLEAN AIR COMPRESSED SYSTEM FILTER MOISTURE
Manual twist drain to to release built up liquid and debris from the system. located on the bottom of the bowl
Compressed air filters protect your equipment from dust, dirt, oil and water. Dust will wear down your equipment (like the air motor in grinders, pneumatic actuators and it can make pneumatic control valves get stuck.
Especially when the dirt and dust is combined with oil (which is often the case with compressors), a sticky mess can form inside valves, motors and other compressed air equipment.
Find the cheapest prices on Moisture Compressed Air from certified, secure, trusted merchants, stores, and retailers at aDealaLot.com. Compare the cheapest prices from across the internet in seconds and save time and money. Shopping the internet for the best prices has never been so easy. Comparison shop trusted, certified merchants on secure websites from across the internet, and always find the best price. Find the total price from unbiased shopping merchants and read reviews on products and merchants.
How To Remove Moisture From Your Compressed Air
Moisture Compressed Air
Parts that I used for my setup:
Transmission cooler: https://amzn.to/2tvqGhF
Brass flare nuts: https://amzn.to/2MZBWey
Brass flare fittings: https://amzn.to/2lAc9wE
Water separator (auto drains when the trap is full): https://amzn.to/2KiVmJj
Water separator (only drains when the compressor shuts off and the line unloads): https://amzn.to/2MnqfOQ -Good for low duty cycles
Water Seperator that I used: https://amzn.to/2IAxzYo (not cheap or easy to get)
Flare tool: https://amzn.to/2MnJGWB
Tags: Compressed air,how to remove moisture,how to re...