Program steps - STEP1: Low Volt Start (0.5V). STEP2: TEST before charge. STEP3: Temperature check. STEP4: Ultra LOW VOLT SAVE. STEP5: LOW VOLT SAVE / cell monitoring. STEP6: TEST - cell damage. STEP7: Cell-balancing CHARGE. STEP8: OPTIMIZE. STEP9: TEST after CHARGE. STEP10: OptiMate Maintenance. Special features: • Battery SAVE mode with BMS reset : Starts from 0.5V with continuous monitoring / testing of charge acceptance or bad / shorted cell condition. Unnecessary (and unsafe) charging of a bad battery is prevented. • Safety : Automatic charge rate adjustment to ambient temperature sensed at the charger. Reduced charging below freezing, no charging if temperature is below -20C/-4F (can damage lithium batteries). • Amp Matic : Microprocessor adjusts current to ideal LiFePO4 charge curve to match battery size / condition, for fastest and most complete charge. SAFE: No risk of overcharging. Totally safe for vehicle electronics. Sparks suppressed. Safe for long-term battery maintenance. Automatic shut-down if short-circuited or battery disconnected. 3-year limited replacement warranty.
YXQ 0-15V Analog Voltmeter Panel 85C1-V Gauge Meter 2.5 Accuracy for Auto Circuit Measurement Tester (DC 15V-3Pcs)
YXQ 0-15V Analog Voltmeter Panel 85C1-V Gauge Meter 2.5 Accuracy for Auto Circuit Measurement Tester (DC 15V-3Pcs) Range: DC 0 to 15V, 0.5V graduation Measures current tool with accuracy of Class 2.5 ,Clear and easy to read scale and a button for fine tuning the dial
DROK 0.56" LED Digital Voltmeter DC 0-33V 4 Digits 3 Wires Voltage Meter Panel Gauge 12V/24V Volt Tester Power Monitor - 100205
Parameters: Supply voltage: DC7-30V Measuring voltage: DC 0-33V Accuracy: 0.02V Input impedance: About 100Kohm Overload: 4 times of the range Display: 4 digits 0.56 "LED digital tube Display color: Blue Refresh rate: about 300mS / times Working temperature: -40 °c - 85 °c Digital Tube: 61mm x 29mm x 17.5mm Circuit board: 58mm x 26mm Features: Ultra-small, Two-wire Are imported MCU design, software filtering Using automatic SMD process, Comes with two regulator chip, stable Built-in protection against reverse, reverse will not burn, over range is displayed "0" For monitoring automobile, car batteries, motorcycle battery voltage Installation fault self-test: 1. Digits do not shine. Check if the red wire and black wire reversely connected; Check if the voltage of red wire is 7-24V. 2. The voltmeter display “0”. Check if the green wire connects well; Check if the voltage is “0” . 3. Voltmeter highest bit shows "1". Check if the green wire connects well. 4. Digital bounce. Check if the voltage of red wire (connect to power supply) is stable. Check if three wires is good connected. Package include: 1x Digital Voltmeter
Tekpower TP7244L 7-Function 20-Range Analog Multimeter With Back Light with Strong Protective Holster
The Tekpower 7244L is a 20-Range Analog Multimeter, which you can use to measure AC/DC voltage, DC current, resistance, continuity, decibel values/dB and diode test. This meter is well known for its accuracy at its low DC voltage and current measurement, to measure a DC voltage under 10 volts, you have four ranges to choose, they are 0.1V, 0.5V, 2.5V and 10V. For DC current, you can measure current as low as a few micro amps using the 50 micro amp range with 3% accuracy. General Specifications: *Power: 2 X AA, *Battery life: 10 hours of continuous use, *Dimensions: 6 1/2" X 3 1/2" X 1 1/2" *Weight: 11.3 Oz, *Fuses: 250 mA / 250 V & 10 A / 250 V. Technical Specifications: *DCV: 0 - 100 mV ± 0.5%/ 500 mV / 2.5 V / 10 V / 50 V / 250 V / 500 V ± 3.0%, *ACV: 0 - 10 V / 50 V / 250 V / 500 V ± 4.0%, *DCA: 50 ?A / 2.5 mA / 25 mA / 250 mA / 10A ± 3.0%, (all ranges fused), *Resistance:2K / 20K / 200K / 2M / 20M Ohm ± 3.0%, *Continuity, *Decibel value *Diode Test. Package includes: *7244L Analog Multimeter, *Test leads with shrouded plugs and capped tips, *User Manual Please refer to the comparison chart in the image to choose your favorite meter from Tekpower, you will find the best one you need from Tekpower.
Power Analyzer - JZCreater Watt Meter Power Analyzer, High Precision RC with Digital LCD Screen for voltage (V) current (A) Power (W) Charge(Ah) and Energy (Wh) Measurement 130Amps
JZCreater, quality product within your reach! The JZCreater High Precision Watt Meter and Power Analyzer is designed to measures up to 60V and 130A. The blue backlit LCD display is clear, bright and easy to read with continuous real time displays of amps, volts, and watts ect. This is the perfect troubleshooting multifunction tool. This all-in-one watt meter is indispensable for analyzing, testing and troubleshooting any other DIY DC power project. Main Feature: Working voltage: 0 to 60 Volts. Easy To Use: Requires no configuration or programming. Digital LCD screen: Easy to read LCD screen provides clear number readings. Real Time Reading: The Watt Meter will continuously provide real time readings of the amps, volts, and watts after connection. (All Measurement screen value are updated every 0.4 second) Test Range and Display format: Operates from 4.8-60V (0V with optional auxiliary battery) Measures 0-60V, 0-130A, 0-6554W, 0-6554Wh, 0-65Ah Voltage test range: 0~60V, resolution 0.01V. Current test range: 0~ 130A, resolution 0.01A. Active Power test range: 0~6554W, resolution 0.1W. Energy test range: 0~6554Wh, resolution 0.1Wh. Charge test range: 0-65Ah, resolution 0.001Ah. Packing including: 1 * 0-60V 130A Watt Meter and Power Analyzer. 1 * Manual
Zeltauto LCD Digital Car Voltmeter 12V/24V Vehicle Voltage Gauge Monitor for Auto Car Truck
Zeltauto LCD Digital Car Voltmeter 12V/24V Vehicle Voltage Gauge Monitor for Auto Car Truck Specifications: Color: Black Screen digital color: Red Apply for: DC 12V or 24V car Input voltage: 12V/24V Output voltage: DC 12-24V Measuring range: DC 8V-30V+-1.2% When engine running (do not drive), LED display: Between 13.5 to 14.5 (12V Car), between 26.0 to 28.0 (24V Car) When engine off, and nothing turned on, LED display: Greater than 12.0 (12V car) or 24.0 (24V car) Installment: Clean the cigar socket. Insert the jack of the product into a cigar socket. Advantages: With high brightness of LED (light-emitting diode) there is no difficulty in seeing the display. This digital gauge displays the voltage of batteries in the car. Package: 1 x Electric Voltage Meter
AimoTek ACM03 Plus Auto Range Digital Clamp Multimeter AC DC Current Voltage Resistance Capacitance Hz Meter Tester NCV Function
Features:It is designed according to IEC1010-1 and IEC1010-2-032 concerning safety requirements.Safe and professional3999 counts digital LCD displayAuto/Manual rangeUse for measure AC/DC current, AC/DC voltage,resistance, capacitance, frequency, diode and circuit, etc.Continuity test, duty cycle test Non contact voltage detectorClamp lighting & back light.Data holdSpecifications:DCV: 400m/4V/40V/400V±0.8%, 600V ±1.0% ACV: 4V/40V/400V/600V±1.2%ACA: 40A/400A±3.0%DCA: 40A/400A±3.0%Resistance: 400?/4k?/40k?/400k?/4M?±1.2%, 40M?±2.0%CAP: 40nF/400nF/4?F/40?F/100?F±3.0%Frequency: 50Hz/500Hz/5kHz/50kHz/100kHz±1.0%NCV:90-1000V(50-500Hz)Duty Cycle: 0.1~99.9% ±3.0%Diode / ContinuityFunctionRangeResolutionAccuracyDiode 1V0.001VDisplaying approximate forward voltage of diodeContinuity Built-in buzzer sounds when resistance is lower than 50ohm.Open circuit voltage: approx. 0.5VOverload protection: 600V DC or True RMS AC
Dr.meter PM2016A Auto-Ranging Digital Clamp Meter, Multimeter with Voltage, AC Current and Resistance Capacitance Tester
Dr.meter PM2016A Digital Clamp Multimeter PM2016A makes household electricity maintenance safe and simple. It enables measuring AC/DC voltage, AC current, resistance and continuity via one button press without needing to break circuits or come into direct hazardous contact. Press Hold button to lock the reading on the LCD display for your convenience. Specifications - AC current: Max. 200A, accuracy ±(2.5% Reading + 8 digits) - DC voltage: Max. 600V, accuracy ±(0.5% Reading + 3 digits) - AC voltage: Max. 600V, accuracy ±(0.8% Reading + 5 digits) - Resistance: Max. 6kΩ, accuracy ±(0.8% Reading + 3 digits) - Max display value: 6000 numbers - Over range indication: '0L' or '-0L' - Sampling rate: approx. 3 times per second - Auto off time: 10 minutes - Power supply: 2 x 1.5V AAA battery - Dimensions: 155 x 45 x 25 mm - Weight: 134g Package Contents 1 x Dr. Meter PM2016A Clamp Digital Multimeter 1 pair x Test Lead 2 x AAA battery 1 x User Manual 1 x Warranty Card Seller Warranty - 12-Month Replacement Warranty - 30-Day Money Back Guarantee - Lifetime Support Guarantee
Tekpower 7-Function 20-Range Analog Multimeter, TP7244
The Sinometer 7244 is a 20-Range Analog Multimeter, which you can use to measure AC/DC voltage, DC current, resistance, continuity, decibel values/dB and diode test. This meter is well known for its accuracy at its low DC voltage and current measurement, to measure a DC voltage under 10 volts, you have four ranges to choose, they are 0.1V, 0.5V, 2.5V and 10V. For DC current, you can measure current as low as a few micro amps using the 50 micro amp range with 3% accuracy. General Specifications: *Power: 2 X AA, *Battery life: 10 hours of continuous use, * Dimensions: 6 1/2 X 3 1/2 X 1 1/2 Inches *Weight: 11.3 Oz, *Fuses: 250 mA / 250 V & 10 A / 250 V. Technical Specifications: *DCV: 0 - 100 mV ± 0.5%/ 500 mV / 2.5 V / 10 V / 50 V / 250 V / 500 V ± 3.0%, *ACV: 0 - 10 V / 50 V / 250 V / 500 V ± 4.0%, *DCA: 50 uA / 2.5 mA / 25 mA / 250 mA / 10A ± 3.0%, (all ranges fused), *Resistance:2K / 20K / 200K / 2M / 20M Ohm ± 3.0%, *Continuity, *Decibel value *Diode Test. Package includes: *7244 Analog Multimeter, *Test leads with shrouded plugs and capped tips, *User Manual
Brand new pressure transducer. Input: -14.5 psi (-1.0 bars) to 30 psi (2.0 bars) Output: 0.5V - 4.5V linear voltage output, see chart below. Works for boost vacuum chamber, oil, fuel, water or air pressure. Can be used in oil tank, gas tank, etc. Accuracy: within 1.5% of reading (full scale). Current draw: less than 4 mA. Burst (over or max pressure) pressure: minimum 100 psi. Thread: 1/8"-27 NPT. (see our fitting set for other thread size below). Wiring connector: water sealed quick disconnect. Mating connector and wire harness (pigtail) is included. Wiring: Red for +5V. Black for ground. Blue for signal output. Our material is using top of line 316 stainless steel (not 304) and high temperature auto-graded plastic. This is a high quality pressure sender, with ceramic pressure chip sensor inside. Specs: www.intindustry.com/files/Pressure_transducer_specs.pdf
Tips to find the best prices on 0.5v Circuit Tester. Always take into consideration specials, rebates or other savings, including shipping, handling and taxes. aDealaLot Search Engine will always search for these offers, including the total cost, and provide you with the best price. New products, merchants and services are always being added to help you save time and money. Compare prices, read reviews on products and merchants and find specials not offered anywhere else.
Premium Digital LED Automotive Circuit Tester
0.5v Circuit Tester
Premium Digital LED Automotive Circuit Tester, 3-32V Test Light with 96 Inch PU Extended Spring Wire, Sharp Stainless Probe Vehicle Circuits Low Voltage Light Tester
Wintind premium automotive digital 3-32V DC circuit tester ideal for car truck and various vehicles electrical circuits voltage testing, also for automotive battery, battery charging systems, ignition systems, which is a must have tool for any automotive engine...